10/11/12

Fanuc alarm: PS270 - OFFSET C START UP CANCEL BY CIR.

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS270 - OFFSET C START UP CANCEL BY CIR.
Alarm Description

Cutter compensation is being started up or cancelled under the arc mode.

Additional Suggestions & Alarm Clarification

CNC Program problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS270 - OFFSET C START UP CANCEL BY CIR. message please post comments below.

Fanuc alarm: PS215 - ESCAPE ERROR (PTRR)

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS215 - ESCAPE ERROR (PTRR)
Alarm Description

A retract command is erroneous. (Longer axis is specified in thread cutting.)

Additional Suggestions & Alarm Clarification

CNC Program problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS215 - ESCAPE ERROR (PTRR) message please post comments below.

Fanuc alarm: PS214 - ILLEGAL USE OF G-CODE

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS214 - ILLEGAL USE OF G-CODE
Alarm Description

A G code which shall not be commanded in G12.1 mode is commanded.

Additional Suggestions & Alarm Clarification

CNC Program problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS214 - ILLEGAL USE OF G-CODE message please post comments below.

Fanuc alarm: PS213 - ILLEGAL USE OF G12.1/G13.1

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS213 - ILLEGAL USE OF G12.1/G13.1
Alarm Description

1) Conditions when polar coordinate interpolation is started or canceled are not correct. 2) G12.1 or G13.1 is commanded in the mode except for G40 mode. 3) There is a mistake in the selection of a plane. (Parameter set mistakes/1032, 1033, 1022)

Additional Suggestions & Alarm Clarification

CNC Program problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS213 - ILLEGAL USE OF G12.1/G13.1 message please post comments below.

Fanuc alarm: PS205 - TURRET REG. NOT FINISHED

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS205 - TURRET REG. NOT FINISHED
Alarm Description

Turret indexing is specified without performing the reference point return.

Additional Suggestions & Alarm Clarification

Send machine home as well as try indexing the turret with the manual buttons on the machine to home some turrets before programming them to run.

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS205 - TURRET REG. NOT FINISHED message please post comments below.

Fanuc alarm: - G02.1/03.1 FORMAT ERROR

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
- G02.1/03.1 FORMAT ERROR
Alarm Description

The command arc exceeded the range where interpolation can be made.

Additional Suggestions & Alarm Clarification

CNC Programming problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: - G02.1/03.1 FORMAT ERROR message please post comments below.

Fanuc alarm: PS201 - ILLEGAL LEAD COMMAND (G35)

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS201 - ILLEGAL LEAD COMMAND (G35)
Alarm Description

A command to change the longer axis is specified during thread cutting in circular thread.

Additional Suggestions & Alarm Clarification

CNC Programming problem

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS201 - ILLEGAL LEAD COMMAND (G35) message please post comments below.

Fanuc alarm: PS200 - PULSE CODER SYNCHRONOUS ERROR

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS200 - PULSE CODER SYNCHRONOUS ERROR
Alarm Description

Grid position could not be obtained because no one-revolution signal was applied before leaving deceleration dog in grid zero return using a digital position detector.

Additional Suggestions & Alarm Clarification

Probably bad encoder possibly cable. Power down machine and back up and rezero machine to see if goes away.

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS200 - PULSE CODER SYNCHRONOUS ERROR message please post comments below.

Fanuc alarm: PS199 - ILLEGAL COMMAND IN INDEXING

CNC Machine Control Manufacturer
Fanuc
Control Model
10/11/12
PS199 - ILLEGAL COMMAND IN INDEXING
Alarm Description

On indexing commands for the index table, error commands are specified.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Any additional suggestions or recommendations on the Fanuc alarm: PS199 - ILLEGAL COMMAND IN INDEXING message please post comments below.
Subscribe to 10/11/12

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer