16/18/21

Fanuc alarm: 466 - n AXIS : MOTOR/AMP COMBINATION

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
466 - n AXIS : MOTOR/AMP COMBINATION

Alarm Description

The maximum current rating for the amplifier does not match that for the motor.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 466 - n AXIS : MOTOR/AMP COMBINATION) error message below.

Fanuc alarm: 465 - n AXIS : READ ID DATA FAILED

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
465 - n AXIS : READ ID DATA FAILED

Alarm Description

At power-up, amplifier initial ID information could not be read.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 465 - n AXIS : READ ID DATA FAILED) error message below.

Fanuc alarm: 464 - nAXIS: WRITEIDDATAFAILED

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
464 - nAXIS: WRITEIDDATAFAILED

Alarm Description

An attempt was made to write maintenance information on the ampli-fier maintenance screen, but it failed.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 464 - nAXIS: WRITEIDDATAFAILED) error message below.

Fanuc alarm: 463 - n AXIS : SEND SLAVE DATA FAILED

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
463 - n AXIS : SEND SLAVE DATA FAILED

Alarm Description

Because of an FSSB communication error, the servo system could not receive correct data.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 463 - n AXIS : SEND SLAVE DATA FAILED) error message below.

Fanuc alarm: 462 - n AXIS : SEND CNC DATA FAILED

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
462 - n AXIS : SEND CNC DATA FAILED

Alarm Description

Because of an FSSB communication error, a slave could not receive correct data.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 462 - n AXIS : SEND CNC DATA FAILED) error message below.

Fanuc alarm: 461 - n AXIS : ILLEGAL AMP INTERFACE

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
461 - n AXIS : ILLEGAL AMP INTERFACE

Alarm Description

The axes of the 2-axis amplifier were assigned to the fast type interface.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 461 - n AXIS : ILLEGAL AMP INTERFACE) error message below.

Fanuc alarm: 460 - n AXIS : FSSB DISCONNECT

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
460 - n AXIS : FSSB DISCONNECT

Alarm Description

FSSB communication was disconnected suddenly. The possible causes are as follows: 1) The FSSB communication cable was disconnected or broken. 2) The power to the amplifier was turned off suddenly. 3) A low-voltage alarm was issued by the amplifier.

Additional Suggestions & Alarm Clarification

Check fiber optic cables for damage

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 460 - n AXIS : FSSB DISCONNECT) error message below.

Fanuc alarm: 453 - n AXIS : SPC SOFT DISCONNECTALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
453 - n AXIS : SPC SOFT DISCONNECTALARM

Alarm Description

Software disconnection alarm of the ? pulse coder.
Turn off the power to the CNC, then remove and insert the pulse coder
cable. If this alarm is issued again, replace the pulse coder.

Additional Suggestions & Alarm Clarification

None currently

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 453 - n AXIS : SPC SOFT DISCONNECTALARM) error message below.

Fanuc alarm: 449 - n AXIS : INV. IPM ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
449 - n AXIS : INV. IPM ALARM

Alarm Description

1) SVM: IPM (intelligent power module) detected an alarm. 2) a series SVU: IPM (intelligent power module) detected an alarm.

Additional Suggestions & Alarm Clarification

Typically the drive needs to be replaced

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 449 - n AXIS : INV. IPM ALARM) error message below.

Fanuc alarm: 448 - n AXIS : UNMATCHED FEEDBACK ALARM

CNC Machine Control Manufacturer
Fanuc
Control Model
16/18/21, 16i/18i/21i, 160i/180i/210i, ,
448 - n AXIS : UNMATCHED FEEDBACK ALARM

Alarm Description

The sign of feedback data from the built-in pulse coder differs from that of feedback data from the separate detector.

Additional Suggestions & Alarm Clarification

Check all cable connections to encoder and drives. Disconnecting cables may loose axes home position. Check for coolant in plugs and encoder area.

Help Others
Post troubleshooting recommendations for (Fanuc alarm: 448 - n AXIS : UNMATCHED FEEDBACK ALARM) error message below.
Subscribe to 16/18/21

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer