MX2

Yasnac MX2 CNC error codes and alarms

Yasnac alarm: 332 - FUSE (Y)

CNC Alarm Error Message
332 - FUSE (Y)
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

FUSE BLOWN Y

Additional Suggestions & Alarm Clarification

Check for Fuses and Breakers on Servo Pack drive.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 332 - FUSE (Y)) error message below.

Yasnac alarm: 331 - FUSE (X)

CNC Alarm Error Message
331 - FUSE (X)
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3, LX1, LX2, LX3

Yaskawa/Yasnac CNC Machine Alarm Description

FUSE BLOWN X

Additional Suggestions & Alarm Clarification

Check for Fuses and Breakers on Servo Pack drive.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 331 - FUSE (X)) error message below.

Yasnac alarm: 320 - NC UNREADY

CNC Alarm Error Message
320 - NC UNREADY
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3, LX1, LX2,

Yaskawa/Yasnac CNC Machine Alarm Description

NC UNREADY P SET NOT READY

Additional Suggestions & Alarm Clarification

The power on circuit for the main control is not ready. There may be another button that needs to be pushed to ready up the control or another machine condition that must be satisfied before NC Ready comes on.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 320 - NC UNREADY) error message below.

Yasnac alarm: 310 - SERVO OFF

CNC Alarm Error Message
310 - SERVO OFF
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3, LX1, LX2, LX3

Yaskawa/Yasnac CNC Machine Alarm Description

SERVO POWER NOT SUPPLIED

Additional Suggestions & Alarm Clarification

Servo Drives are off. Condition exists that is not allowing a power on. Check drives for faults or Fault LEDS.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 310 - SERVO OFF) error message below.

Yasnac alarm: 275 - P-SET ERROR (5)

CNC Alarm Error Message
275 - P-SET ERROR (5)
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

P SET ERROR 5 (IF THIS ERROR OCCURS IN BLOCK WHERE GOO IS CHANGING TO GO1, MACHINE STOPS AFTER COMPLETION OF GOO BLOCK)

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 275 - P-SET ERROR (5)) error message below.

Yasnac alarm: 274 - P-SET ERROR (4)

CNC Alarm Error Message
274 - P-SET ERROR (4)
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

P SET ERROR 4 (IF THIS ERROR OCCURS IN BLOCK WHERE GOO IS CHANGING TO GO1, MACHINE STOPS AFTER COMPLETION OF GOO BLOCK)

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 274 - P-SET ERROR (4)) error message below.

Yasnac alarm: 273 - P-SET ERROR (Z)

CNC Alarm Error Message
273 - P-SET ERROR (Z)
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

P SET ERROR Z (IF THIS ERROR OCCURS IN BLOCK WHERE GOO IS CHANGING TO GO1, MACHINE STOPS AFTER COMPLETION OF GOO BLOCK)

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 273 - P-SET ERROR (Z)) error message below.
Subscribe to MX2

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer