J50

Yasnac J50 CNC control alarms listing.

Yasnac alarm: 329 - PC CPU ERROR

CNC Alarm Error Message
329 - PC CPU ERROR
Control Manufacturer
Yaskawa
Control Model
J50, MX3, LX3

Yaskawa/Yasnac CNC Machine Alarm Description

PC CPU IS IN ABNORMAL STATE. (SET "0" IN #6014 D7 TO RESET THE ERROR).

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 329 - PC CPU ERROR) error message below.

Yasnac alarm: 327 - NO PROG GEN (RES?NEXT?PRG)

CNC Alarm Error Message
327 - NO PROG GEN (RES?NEXT?PRG)
Control Manufacturer
Yaskawa
Control Model
J50, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

MEMORY LENGTH, FOR WHICH MEMORY GENERATION WAS NOT PERFORMED, HAS BEEN CHANGED BUT NO GENERATION HAS BEEN MADE (RES?NEXT?PRG)

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 327 - NO PROG GEN (RES?NEXT?PRG)) error message below.

Yasnac alarm: 325 - SERVO CPU ERROR

CNC Alarm Error Message
325 - SERVO CPU ERROR
Control Manufacturer
Yaskawa
Control Model
J50, MX3, LX3

Yaskawa/Yasnac CNC Machine Alarm Description

SERVO CPU IS IN ABNORMAL STATE. (SET "O IN #6014 D6 TO RESET THE ERROR).

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 325 - SERVO CPU ERROR) error message below.

Yasnac alarm: 322 - CMOS VACANT AREA ERROR

CNC Alarm Error Message
322 - CMOS VACANT AREA ERROR
Control Manufacturer
Yaskawa
Control Model
J50, MX3, LX3

Yaskawa/Yasnac CNC Machine Alarm Description

THE UNUSED AREA OF THE CMOS IS USED. (THE CMOS MAY BE DESTROYED.) (SET "1" IN #6066 D2 TO RESET THE ERROR.)

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 322 - CMOS VACANT AREA ERROR) error message below.

Yasnac alarm: 320 - NC UNREADY

CNC Alarm Error Message
320 - NC UNREADY
Control Manufacturer
Yaskawa
Control Model
J50, MX1, MX2, MX3, LX1, LX2,

Yaskawa/Yasnac CNC Machine Alarm Description

NC UNREADY P SET NOT READY

Additional Suggestions & Alarm Clarification

The power on circuit for the main control is not ready. There may be another button that needs to be pushed to ready up the control or another machine condition that must be satisfied before NC Ready comes on.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 320 - NC UNREADY) error message below.

Yasnac alarm: 315 - 5TH AXIS SERVO UNREADY

CNC Alarm Error Message
315 - 5TH AXIS SERVO UNREADY
Control Manufacturer
Yaskawa
Control Model
J50, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

5TH AXIS SERVO NOT READY

Additional Suggestions & Alarm Clarification

Servo Drives are off. Condition exists that is not allowing a power on. Check drives for faults or Fault LEDS.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 315 - 5TH AXIS SERVO UNREADY) error message below.

Yasnac alarm: 314 - 4TH AXIS SERVO UNREADY

CNC Alarm Error Message
314 - 4TH AXIS SERVO UNREADY
Control Manufacturer
Yaskawa
Control Model
J50, MX3

Yaskawa/Yasnac CNC Machine Alarm Description

4TH AXIS SERVO NOT READY

Additional Suggestions & Alarm Clarification

Servo Drives are off. Condition exists that is not allowing a power on. Check drives for faults or Fault LEDS.

<p></p>
Help Others
Post CNC machine troubleshooting recommendations for (Yasnac alarm: 314 - 4TH AXIS SERVO UNREADY) error message below.
Subscribe to J50

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer